DIY fluorescent LED bulbs provide customizable lighting alternatives for photos, video

    Along with clamp lights, another option for continuous lighting are LED fluorescent tubes.

    Adam from Droi Media did a couple video tutorials in 2019 showing how to make your own light tubes, as well as a mount and dimmer for them. He estimates the costs for the lights at less than $25 a foot.

    Many of you are probably thinking that sounds pretty stiff since you can get a 4-foot LED fluorescent tube for about $63 at a warehouse hardware store. And you'd be right, except for two things: 1. That's just the tube and not the mount or the way to power the light; and 2. You have to buy a 4-foot light.

    Adam's plan allows you to customize the size of the light to fit your cases, and they don't require all the other major hardware you need to power them.

    Basically his design involves wrapping LED strip lights around a wooden dowel, attaching wires for the power supply and inserting it in a frosted tube secured by screws through the end caps and hooked up to a power supply. The hardest skill in the whole thing appears to be soldering wire.

    He also shows how to combine them on a mount with a dimmer switch. It's a great addition for your video or studio photography kit, and being LED, which can also run off batteries, used in the field as well.

PVC lightstands can support flash units with DIY adapter

    As promised, here's how to mount a flash unit on your PVC light stand.

    Everybody is familiar with flash units, especially on-camera flash. Some people started out with the built-in flash, but the first major upgrade is going with a speed light on the hot shoe.

    But if you want to take your flash photography to the next level, you need to get the flash off the camera, allowing you to get better lighting angles than if it's attached to the top of your camera, or on a bracket to the side.

    We won't get into how to trigger the flash, as the DIY options involve some knowledge of electronics and there are options available such as wireless transmitters or using our camera's on-board flash as a "master" to trigger the "subordinate" flashes.

    But the question is how to set the flash up away from the camera. Most speed lights nowadays come with a small cold-shoe base you can attach to the bottom of the flash. This base lets you set it on a table or shelf, but that doesn't help much when there's nothing to sit it on.

    The flash makers recognize that, and these feet have a 1/4x20 hole in the bottom to attach it to a tripod. That's a good alternative, but suppose you need the tripod for a camera, or you don't have the room to set up one or more tripods (they do take up quite a bit of real estate)?

    PVC light stands, particularly the one I built based on Scott Eggelston's (The Frugal Filmmaker) plan, take up one square foot of floor space.

    Using Scott's plan for hacking a worklight, I got a set of four 3/4" PVC end caps to make four flash mounts. While Scott just put a bolt through the cap to attach to the work light, a flash is different, since it would also need to swivel and tilt.

    I found a set of fairly heavy duty ball heads on eBay (I had asked Scott if a ball head he had used in a different project would work for a speed light, but he told me to get something with a greater weight rating.) that could hold a DSLR with lens if needed.

    I attached the head to 1/4x20 bolt through the cap, giving me a mount that can slip over the 3/4" pipe on the lightstand.

    The ball head is fully adjustable and the flash stand attaches easily and securely to it.

Mount your clamp light on a PVC lightstand without the clamp

    In the last post, I talked about how to double the output of a clamp light by using a two-bulb adapter.

    This time, we're going to talk about a better way to mount the lights than with the clamp.

    While the clamp offers a certain level of versatility, there are some drawbacks, especially if you're using the PVC lightstands I highlighted a couple years ago. The clamps sometimes don't grip the pipe just right and may come off at an inopportune moment, or they might throw off the balance of your stand.

    Also, if you're shooting in someone else's home, they may not want you attaching your clamp to their furniture and possibly scuffing it up. (Sometimes the rubber on the clamps wears out.)

    But there's a solution if you use the PVC light stand, as demonstrated by Ryan Connolly over at Film Riot. What Ryan did was replace the clamp with a pipe connector, allowing you to directly connect the light to the stand.

    What you need is a 3/4-inch pipe connector, a bolt, wingnut and a couple nuts if needed. Here's the basic assembly for the mount (before the light is attached).

    First, remove the clamp and get a bolt that will fit the hole that was used by the tiny bolt that held the clamp on. I wouldn't throw away the clamp, as you might want to use it if you're in a situation where you can't use a lightstand.

    Then, drill a hole through both sides of the connector to thread the bolt through. In my case, I needed to put a couple extra nuts on to ensure the clamp mount didn't come apart. On the other side, put the wingnut, as this will let you control the vertical angle of the light.

    This is the finished product, attached to a stand.

    Scott Eggleston, of the The Frugal Filmmaker, offered a similar solution for mounting shop lights on a PVC stand, except using end caps.

    In our next post, I'll show you how to use that technique for flash units.